EZ-FLOW LEVELER GLOSS ENHANCER

EZ-FLOW LEVELER GLOSS ENHANCER
Click over image to enlarge
Price: $21.95
 
Weight: 5.00 lbs
More images
EZ-FLOW LEVELER GLOSS ENHANCER
Click over image to enlarge
Purchase
SIZE :
Quantity :
 
Overview
Reduces Orange Peel- Dry Dust - Less Reduction with small 2-3 Stage Turbines - Eliminates Dry Edges - Helps Gloss - Keep A Wet Edge
Description

BENEFITS :

 

  • CONTROLS PIN HOLING 
  • HELPS STOP DOWN GLOSSING LOSS OF GLOSS WHEN FINISHED IS DRIED 
  • HELPS to ELIMINATE BUBBLES in FINAL FINISH
  • REDUCES ORANGE PEEL-DRY 
  • ELIMINAtES DUST Associated with FAST DRY COATINGS & HOT AIR TURBINES
  • ELIMINATES RIPPLE EFFECT ON TILE WALLS and FIBERGLASS SURROUNDS
  • HELPS To ACHIEVE A GEL COAT LIKE FINISH  ON FIBERGLASS UNITS & CULTURED MARBLE
  • STEPS UP GLOSS
  • ELIMINATES A DRY EDGES
  • KEEPS A WET EDGE
  • MANUAL SPECKING COUNTERS are MORE REALESTIC as EZ-FLOW allows EACH COLOR TO Blend and FLOW INTO EACH OTHER 



 


Description & Over View :

 

 

EZ-FLOW reduces the amount of solvent necesarry to thin and spray HIGH SOLID urethanes

and epoxy coatings. SharkGrip Modified Epoxy contains over 13LBS of Titanium.

Over Reduction Of this Product is mainly due to under powered HVLP TURBINE SPRAYERS

trying to atomize such Solid Coatings.  It is the leading and number one contributor for negative

reactions while second only to improper preparing of the surfaces.  Common examples of these negative

reactions are fish eyes, blushing, pin holes, and die back or loss of gloss after curing.

Until refinishers are made aware of these facts over reduction  will remain a

serious and frequent problem in the bathtub refinishing industry. 


How frequent? The level of frequency can be measured by how many refinishers are still

spraying using  2 and 3 stage hvlp turbine units everyday. 

 

How is this possible?  The explanation can easily found by simply following the history of

refinishing and more precisely the coatings that service it. Looking back 10 to  15 years

ago bathtub refinishers were spraying 30% - 45 % to 50 % solid coatings or low to

medium solid coatings. At that time a two or three stage hvlp turbine with 15 % reduction

was adequate to achieve fine atomization. However, as VOC LAWS in time VOC laws

increased and so did the necessity to develop higher solids coatings to comply with these

new laws. As the Solids increase coats become harder to atomize. Instead of increasing the

power of the spray equipment by upgrading to 4, 5 or 6, stage Turbines like the Capspray 95 105 or  115,

bathtub refinishers hace compensated by simply adding excessive amounts of reducer.

Either igonoring the fact or not realizing the detrimental effects to refinishing coatings.

To illustrate this see the below below example of a common mix necessary to attain fine

atomization using 2 or 3 stage turbine sprayers.

12 Ounces Part A 

12 Ounces Part B, and 

 8 to 12 Ounces redcuer.

 Basically a 1-1-1 ratio. If your mix resembles the example given and you are experiencing

any of negative effects or failures EZ-FLOW will help.

While most will experiece the immediate problems of excessive reducer such as the pin holes,

blushing, loss of gloss aka die back, fish eyes, bubble, many refinishers fail to realize that there

are long term negative effects. Impact resistance is lessened, adhesion is weakened, gloss and

chemical resistance negated.

What's the Answer? Upgrading the equipment is the obvious answer as we know there's no replacement for displacement. 


If buying the correct equipment is impractical at this time  EZ-FLOW can help you compensate.


 How to Use EZ-FLOW ?  If your using EZ-FLOW for its leveling and small turbine compensating factors then here is an example of a mix for SharkGrip Epoxy on a bathtub.

12 Ounces Part A

12 Ounces Part B

Allow to induct, add 3 Ounces Epoxy Thinner and 3 Ounces EZ Flow and spray.


EZ-FLOW is NOT A REDUCER and WILL NOT DEGRADE YOUR COATINGS

WHILE EASY FLOW IS A SOLVENT SOLUTION we EAH ENCOURAGES YOU TO KEEP UP WITH TECHNOLOGY AND UPGRADE YOUR SPRAY EQUIPMENT

TITAN CAPSPRAY HAS A GREAT SPECIAL through MAY 2016

Models Capspray 95 - Capspray 105 and Capspray 115



 

 

Recommended Products
Aditives
TRUE GRIT SLIP RESISTANT PARTICLES "16OZ"
TRUE GRIT SLIP RESISTANT PARTICLES "16OZ" Product ID : TG16
Price: $18.39
Browse more in Additives category
Click to view
MELT DOWN GLOSS ENHANCER & REPAIR BLENDER
MELT DOWN GLOSS ENHANCER & REPAIR BLENDER
Product ID : MD-G
Price: $89.00
Browse more in Additives category
Click to view
FAST FLECK - Multispec Accelerator 1 Gal
FAST FLECK - Multispec Accelerator 1 Gal Product ID : FF-1
$39.95  Sale Price: $21.95
Browse more in Multi-Spec category
Click to view
ROCKET UNIVERSAL URETHANE ACCELERATOR 1 QT
ROCKET UNIVERSAL URETHANE ACCELERATOR 1 QT Product ID : ROCK
Price: $26.95
Browse more in Additives category
Click to view
image